Tel:+86-0512-63419655   E-mail:ndt@desisengroup.com
/
/
/
SUZHOU DESISEN
ELECTRONICS CO., LTD.
Home / Products / Sorting Machine / Automatic Screw Hardware Sorting Machine
Product Category

Get In Touch

Tel: +86-0512- 63419655
Phone: +86-13616209379
Fax: 0512-63459655
Email: ndt@desisengroup.com

Contact Us
Share to:

Automatic Screw Hardware Sorting Machine

When the workpiece to be measured passing through the probes uniform distributed in magnetic field, which will create a changing magnetic field, the changing magnetic field will generate corresponding magnetizing current in coil then transmitted to the instrument through the wire, after analyzed by instrument center circuit, compared the quality condition of workpiece to be measured, the result will be shown on display screen, at the same time, the hardness qualified signals of workpiece to be measured, exceeding the maximum limit range of hardness, and lower the minimum range of hardness signals will be transmitted to automatic separating mechanism, therefore the automatic separation of workpiece is realized.

  • EHS-3X

Product Description

Introduction:




When the workpiece to be measured passing through the probes uniform distributed in magnetic field, which will create a changing magnetic field, the changing magnetic field will generate corresponding magnetizing current in coil then transmitted to the instrument through the wire, after analyzed by instrument center circuit, compared the quality condition of workpiece to be measured, the result will be shown on display screen, at the same time, the hardness qualified signals of workpiece to be measured, exceeding the maximum limit range of hardness, and lower the minimum range of hardness signals will be transmitted to automatic separating mechanism, therefore the automatic separation of workpiece is realized.


Features:


1. Used for 100% nondestructive on-line automatic separating of qualified and unqualified bearing hardness after heat treatment. Qualified hardness of bearing will be transmitted by the conveyor belt to next station, and unqualified hardness of bearing will be automatically removed by the separation barrier gate.

2. For respective counting of qualified and unqualified hardness of bearings (upper limit and lower limit).

3. Master instrument of separator can dynamically display bearing hardness condition with histogram. The amplitude of histogram reflects the hardness of bearing to be measured, intuitive is strong. After calibration, it can display hardness value of the bearing being measured.

4. There are hardness range upper limit and lower limit setting keys on master instrument of separator convenient for the operator to use, when the hardness of measured bearing exceeding upper limit or lower limit, instrument will send out corresponding light and sound alarm, and qualified and unqualified signals will be sent to actuator for separating.

5. There is status display light of bearing hardness on electrical control box panel of separator, bearing hardness is qualified and green light will light on, bearing hardness is unqualified, then the red light will light on (exceed upper limit or below the lower limit), when bearing hardness unqualified, it will send out sound and light alarm.

6. Automatic Screw Hardware Sorting Machine has features of jam alarm (installed at stocker, feed opening), frequency converter fault alarm, alarm for stocker door not withdrawn in time, automatic stop after fault alarm, and automatic startup after troubleshooting. The corresponding fault at the same time will be displayed on the display screen.

7. Master instrument of separator can store upper limit and lower limit of flux value of 10 kinds of different specifications and dimensions of bearing, and No. 1, 2, 3, 4, ┉ 10 respectively represent different size of bearing to be measured, convenient for user to direct call.   


Parameters:



1·Detection speed: Due to different specifications of bearing are adjustable, not less than 600 per hour.

2·Detection accuracy: Rockwell hardness: <±1HRC.

3·Weight: 500Kg.

4·Compressed air pressure range: 0.15Mpa-0.8Mpa. 

5·Bearing to be measured shall meet the following requirements: The same kind of material, the same size, the same surface state and the same system of heat treatment process

6·Overall dimensions of the equipment: 

Mechanical drive part: L×W×H=2200×920×1450mm (customizable).

Main electric control cabinet: L×W×H =560×570×1530mm  (customizable).


Working environment:




Operating temperature: -15~55℃

Storage temperature: -20~60℃

Relative humidity: less than 85%

Working voltage: AC220±10V


A view of separation test:

EHS-3X

A view of separation test:

EHS-3X-1

Get In Touch

Tel

+86-0512-63419655 / +86-13616209379
Email
ndt@desisengroup.com
Adress
Building 31, U TechnoPark, No 4168 Dongshan Avenue, Wuzhong District, Suzhou City, Jiangsu Province, China.

Quick Links

Product Links

Contact Us
©  2019 Suzhou Desisen Electronics Co., Ltd.  All rights reserved. Sitemap.